projects4ufriends

There are several sets of circumstances that can return this status. A. If the drive has not been partitioned (with FDISK) this message will be reported. B. If the drive parameters (Cyl, Hd, Sec) set in CMOS DON'T match those of the drive this message will be returned indicating that the drive geometry read from the drive doesn't match what is entered in CMOS. C. General hardware failure on the disk sub-system where the drive geometry cannot be read (causing the mismatch described in B). This could be a bad cable, misplaced cable (off by a pin or row) no DC power to the disk, bad disk PCB, incorrect jumpering on disk PCB. Any matter of problems that can cause the disk to be unreadable can return this error message. NOTE!! On initial HDD install/upgrade I'd do a physical check on all the obvious things like cable placement, power connectors, listen to hear the disk seeking during it's POST test on pwr up. If this error occurs after the disk has b...

If your computer has just been formatted, your computer might require you to insert the boot CD to be able to run it. You might hence get the error message “Disk Boot Failure- Insert disk and press enter” displayed on the screen every time you will try to run it. This might be linked to: 1. The boot options not correctly set in BIOS 2. A non bootable CD is found in your CD drive 3. You do not possess any bootable device 4. You have installed a new hard disk 5. The hard disk is not properly plugged 6. Your system files have been infected Solution 1: Ensure that your drives are empty If there is a non bootable CD or disk in the drives, your computer might be attempting to boot the program with this disk. Hence, ensure that the floppy disk drive, the CD/R and DVD drives are all empty before restarting your computer and trying to run computer again. Solution 2: BIOS set up If this has not solved the problem, it might be linked to a wrong set up of BIOS. Hence, 1. To enter...

It often happens that while trying to delete a file or a folder, your system tells you that this particular file cannot be deleted at that time. These errors occur currently with video or music file formats. This can be due to a number of factors, such as: Someone else is accessing the file/folder on the network or on a shared computer You are trying to delete a system file that is being used by another program You are trying to delete an infected folder or your system has been infected and prevents you from deleting this file You have access restrictions on this particular file/folder The file/folder has been saved in “Read only” format Your system is not compatible with this kind of file and is hence displaying error messages. Here are 5 solutions for that..... Solution 1: Ensure that the file/folder is not in use If you are using a shared computer, another user or program on the user’s account might be using the file/folder that you are trying to delete. 1. Ask the ot...

DLL files form part of a large record of codes and information that are used by many of the programs on your computer system. They are all linked to the Windows Registry and help to enhance the speed and memory effectiveness of your computer by using an identical code to run various tasks processed by various programs at a time. Hence, the rundll error arises when a program is not granted access to this particular code. " Error Loading C:\windows\system 32\bridge.dll " is the kind of rundll error message that you can get. Why does this happen? This error can arise because a DLL file has been infected by a virus or is missing on the system due to a spyware. As the programs using this file will not be able to access it, there will be a rundll error to tell your system that the program cannot be loaded due to the missing code/file. How to fix a rundll error? To be able to locate where the error comes from, you can make use of internet tools or choose to fix it...

If your PC is taking ages to boot up and is very slow while running programs, it might be due to a number of factors. Problem 1: Not enough RAM RAM stands for Random Access Memory and is used as a temporary storage memory by your computer. This memory is in use when tasks are being executed by different programs. Hence, you should have enough RAM memory to process all the tasks at hand; if you don’t this might cause the major slow down of your computer while it is booting up or processing tasks. How to know if your computer has enough RAM? The programs that are installed on your computer usually have RAM requirements that are asked. If your computer has been running at a normal speed before the installation of such programs and has crucially slowed down with time, you might need to add more RAM on your computer system. Also, if your computer is slowing down every time you are processing large files, or it freezes while executing several programs at once, these might be ...

My programs are launching no more It may happen that only executable files aren’t eager open properly: either you have the dialog box "Open With", it opens with notepad or another program. This problem may be due to a error made on your PC. If this is not the case, then it is necessarily a virus, follow this tip to disinfect your PC. To correct the problem, follow these steps: First Solution This solution is valid for XP and 2000 versions. Go to Control Panel and then Folder Options. Select the File Type tab and then click New Type in EXE file extension and click OK The EXE extension is automatically selected, then click Restore Close the dialog box Second solution This solution works for all versions of Windows Click on Start> All Programs> Accessories> Notepad Select the text below> copy and paste it into Notepad Windows Registry Editor Version 5.00 [HKEY_CLASSES_ROOT\exefile] "EditFlags"=hex:d8,07,00,00 @=...

Windows Vista’s Disk Management tool can be quite deceiving. It allows you to work with partitions at ease in a presentable GUI format - but with problems. There have been a lot of complaints and confusion as to why Windows Vista grays out the extend volume and shrink volume properties. In response to this, I have found an alternative way to work with partitions, allowing you to easily resize, delete, and create partitions. Diskpart.exe does a very good job at working with partitions. Unlike Disk Management, Diskpart actually works! Before continuing, make sure that you: * Backed up all important files * Do not run diskpart.exe with Dynamic Disks 1) First, you’ll want to pull out your Start Menu and type diskpart.exe (Windows XP users might have to download diskpart.exe ) This will open a command-prompt like window. At this window, type list disk. This will list all your available hard disks. 2) Proceed by typing select disk to select the disk you want t...

One Beep : DRAM refresh failure This may be due to - Bad memory chips - A bad DMA Chip - Bad memory addressing chips on the motherboard Two Beeps : Parity error or Parity Circuit failure -Your memory may not be seated properly on the mother board. -Unplug and plug it properly Three Beeps : Bad memory or bad mother board Four beeps : Timer failure in the RAM. Five Beeps : CPU chip may be dead Six Beeps : Keyboard controller may have failed Seven beeps : CPU is dead. Retry the connections and test. -Replace the whole motherboard. Eight Beeps : Video card is missing or Bad. Nine Beeps : Damaged ROM BIOS. -BIOS chip has to be replaced if it persists. Ten Beeps : CMOS shutdown. -Replace CMOS memory and associated chips. Eleven Beeps : Cache memory test has failed. -To enable cache memory try CTRL+ALT+SHIFT++. One long Beep and Three short Beeps: Memory failure One long Beep and Eight short Beeps : Video card failure. -Try to install video card in another slot. No Beeps : Che...

When you click on the SHUTDOWN button, make sure to simultaneous press SHIFT Button. If you hold the Shift key down while clicking on SHUTDOWN button, your computer would restart without restarting the Computer. This is equivalent to term "HOT REBOOT".

Forgot Account Password?Then here is the solution for that........... Go to Run->cmd type AT (time) /interactive “cmd.exe” enter time in 24hr format means if you want to enter 5.00pm then enter 17:00 then a new window of cmd will open at specified time. In new window type net(space)user press enter after this u will see some names on ur screen notedown the name of admin acc then type net user (name of admin acc u want to crack into) (space) * e.g if the name of admin acc is john then type net user john * then it will ask u for new password enter password of ur choice and u got the admin password The above scheduling is optional you can crack ur administrative account without doing that.U can perform the following directly from the same window.U should be logged in any account to perform this. for eg :If ur system is a single user system then one inbuilt secret account will be there.How to login into that??Its so simple my dear friends........ U just click CTRL+ALT+DEL ...

Very useful when you have to leave your system on for some time and you have to go some where else... Right click on an empty area of the desktop and choose 'new' then 'shortcut.' The create shortcut wizard will open. in the first text box, type '%windir%\System32\rundll32.exe user32.dll,LockWorkStation' and then give your shortcut an appropriate name on the next page, and hit 'finish.' You will notice that the shortcut you created has a blank icon. To select a more appropriate one, right click on the shortcut and hit 'properties.' In the 'shortcut' tab, click the 'change icon' button. else u can simply press the "window key + l" to lock your computer...

inbuilt blutooth sftware in win. XP Now u don't need 2 install any software for ur bluetooth device. u don't know bt u already had it in ur window xp nd vista it can b used as:- 1.open d run command 2.nw typ 'fsquirt' wid-out quotes 3.nw jus select weder u want 2 snd or receive ne file vry easy:-) NOTE:BLUETOOTH DEVICE NEEDED

What i prefer is %temp% " without quotes.. at Start -> Run.. This opens ur temp folder n den u select all and delete.still try dis one too.. First go into gpedit.msc Next select -> Computer Configuration/Administrative Templates/Windows Components/Terminal Services/Temporary Folder Then right click "Do Not Delete Temp Folder Upon Exit" Go to properties and hit disable. Now next time Windows puts a temp file in that folder it will automatically delete it when its done! Note from Forum Admin: Remember, GPEDIT (Group Policy Editor) is only available in XP Pro.

S tep1: Remove autorun.inf files from all your drives, include any usb/flash drives. 1. Manually: Reboot your PC in Safe mode. 1. Restart your computer 2. After hearing your computer beep once during startup, but before the Windows icon appears, press F8. 3. Instead of Windows loading as normal, a menu should appear 4. Select the first option, to run Windows in Safe Mode. Click Start -> Run. In the type box enter cmd and press Enter. In the command console type del /a:h /f c:\autorun.* Repeat previous step to all drives, make replacing “c” with the appropriate drive letter. 2. Automatically. Download Flash_Disinfector by sUBs and save it to your desktop. Double-click Flash_Disinfector.exe to run it and follow any prompts that may appear. The utility may ask you to insert your flash drive and/or other removable drives including your mobile phone. Please do so and allow the utility to clean up those drives as well. Wait until it has finished scanning and then exit the ...